manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 282 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 282

Principles Of Operation 

Teledyne ML - T101 Operation Manual

 

278

 

10.7.3.

 

TEMPERATURE AND PRESSURE COMPENSATION (TPC) 

FEATURE 

As explained previously, changes in temperature can significantly affect the amount of 
fluoresced UV light generated in the instrument’s sample chamber. To negate this effect 
the Model T101 maintains  the sample gas at a stable, raised temperature. 

Pressure changes can also have a noticeable, if more subtle, effect on the H

2

S 

concentration calculation. To account for this, the Model T101 software includes a 
feature which allows the instrument to include a compensation factor in the H

2

S 

calculations  that is based on changes in ambient pressure. 

When the TPC feature is enabled, the analyzer’s H

2

S  concentration is divided by a 

factor called 

PRESSCO

 which is based on the ratio between the ambient pressure of the 

sample  gas and standard atmospheric pressure (Equation 10-5). As ambient pressure 
increases, the compensated H

2

S concentration is decreased. 

A)

-

HG

("

 

29.92

_SLOPE

SAMP_PRESS

A)

-

HG

("

 

SSURE

SAMPLE_PRE

PRESSCO

×

=

 

Equation 10-5 

SAMPLE-PRESSURE

: The ambient pressure of the sample gas as measured by the 

instrument’s sample pressure sensor (see Figure 10-7) in “Hg-A. 

SAMP_PRESS_SLOPE

: Sample pressure slope correction factor.  

Section 4.5 describes the method for enabling/disabling  the TPC feature. 

10.7.4.

 

INTERNAL DATA ACQUISITION SYSTEM (DAS) 

The DAS is designed to implement predictive diagnostics that stores trending data for 
users to anticipate  when an instrument  will  require service. Large amounts of data can be 
stored in non-volatile memory and retrieved in plain text format for further processing 
with common data analysis programs. The DAS has a consistent user interface in all 
Teledyne  ML instruments. New data parameters and triggering events can be added to 
the instrument as needed. 

Depending on the sampling frequency and the number of data parameters the DAS can 
store several months of data, which are retained even when the instrument is powered 
off or a new firmware is installed. The DAS permits users to access the data through the 
instrument’s front panel or the remote interface. The latter can automatically download 
stored data for further processing. For  information on using the DAS, refer to Section 
4.8. 

 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов