Teledyne T101 Скачать руководство пользователя страница 139

Страница: 139 / 375

Teledyne ML – T101 Operation Manual

Operating Instructions

135

To configure the parameters for a specific data parameter, press:

FROM THE EDIT DATA PARAMETER MENU

(see previous section)

SETUP X.X

0) PARAM=S2SCN1, MODE=AVG

PREV NEXT

INS DEL EDIT EXIT

SETUP X.X

PARAMETERS:S2SCN1

SET> EDIT

EXIT

SETUP X.X

SAMPLE MODE:AVG

<SET SET>

EDIT

EXIT

SETUP X.X

PARAMETERS: S2SCN1

PREV NEXT

ENTR

EXIT

Cycle through list of available

Parameters.

ENTR

accepts the new

setting and returns to the

previous menu.

EXIT

ignores the new setting

and returns to the previous

SETUP X.X

SAMPLE MODE: INST

INST AVG MIN MAX

EXIT

Press the key for the desired mode

SETUP X.X

PRECISION: 1

<SET SET>

EDIT

EXIT

SETUP X.X

PRECISION: 1

EXIT

Set for 0-4

SETUP X.X

STORE NUM. SAMPLES: OFF

<SET

EDIT

EXIT

SETUP X.X

STORE NUM. SAMPLES: OFF

OFF

ENTR EXIT

Turn ON or OFF

<SET

Returns to

Functions

4.8.2.5.

Sample Period and Report Period

The DAS defines two principal time periods by which sample readings are taken and
permanently recorded:

SAMPLE PERIOD

: Determines how often DAS temporarily records a sample reading

of the parameter in volatile memory. The

SAMPLE PERIOD

is set to one minute by

default and generally cannot be accessed from the standard DAS front panel menu, but is
available via the instrument’s communication ports by using APICOM or the analyzer’s
standard serial data protocol.

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 139 / 375

Результаты поиска

Содержание T101

Отзывы: