Teledyne T101 Скачать руководство пользователя страница 318

Страница: 318 / 375

Teledyne API T/E-Series Models 101, 102, and 108 Software Documentation (PN05492D DCN6485)

A-24

TEST Measurement

Message Text

DESCRIPTION

PMTTEMP

PMT TEMP=7.0 C

PMT temperature.

IZSDUTY

IZS ON=0.00 SEC

IZS temperature control duty cycle.

IZSTEMP

IZS TEMP=52.2 C

IZS temperature.

CONVTEMP

CONV TEMP=315.0 C

Converter temperature.

SO2 SO2=261.4

PPB

concentration for current range.

H2S/TRS H2S/TRS=331.6

PPB

S/TRS concentration for current

range.

TRS

TRS=378.4 PPB

TRS concentration for current range.

TESTCHAN

TEST=3721.1 MV

Value output to TEST_OUTPUT

analog output, selected with

TEST_CHAN_ID

variable.

CLOCKTIME

TIME=10:38:27

Current instrument time of day

clock.

The name is used to request a message via the RS-232 interface, as in “T BOXTEMP”.

Engineering

software.

Current instrument units.

T101,

M101E.

Triple-gas

option.

T108,

M108E.

Concentration alarm option.

T108U, M108EU.

Optional.

07266B DCN6485

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 318 / 375

Результаты поиска

Содержание T101

Отзывы: