manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 276 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 276

Principles Of Operation 

Teledyne ML - T101 Operation Manual

 

272

 

board. It is digitized and sent to the CPU where it is used to calculate the current 
temperature of the PMT. 

This measurement is stored in the analyzer’s memory as the test function

 PMT TEMP

 

and

 

is viewable

 

as a test function (Section 4.2.1) through the analyzer’s front panel. 

SAMPLE GAS PRESSURE SENSOR: This sensor measures the gas pressure at the exit 
of the sample chamber. 

SAMPLE FLOW SENSOR: This sensor measure the flow rate of the sample gas as it 
exits the sample chamber. 

10.4.10.3.

 

Thermistor Interface 

This circuit provides excitation, termination and signal selection for several negative 
coefficient thermistor temperature sensors located inside the analyzer. They are: 

SAMPLE CHAMBER TEMPERATURE SENSOR: The source of this signal is a 
thermistor embedded in the of the sample chamber block. It measures the temperature of 
the sample gas in the chamber. This data are used by the CPU to control sample chamber 
the heating circuit and  as part of the H

2

S, calculations when the instrument’s 

Temperature/Pressure Compensation feature is enabled. 

This measurement is stored in the analyzer memory as a parameter (

RCEL TEMP)

 and

 

is viewable

 

as a test function under the same name (Section6.2.1) through the analyzer’s 

front panel. 

IZS  OPTION PERMEATION TUBE  TEMPERATURE SENSOR: This thermistor, 
attached to the permeation tube in the IZS option, reports the current temperature of that 
tube to the CPU as part of control loop that keeps the tube at a constant temperature.

 

BOX TEMPERATURE SENSOR: A thermistor is attached to the motherboard. It 
measures the analyzers inside temperature. This information is stored by the CPU and 
can be viewed by the user for troubleshooting purposes through the front panel display. 
This measurement is stored in the analyzer. Memory as the test function

 BOX TEMP

 

and

 

is viewable

 

as a test function (Section 4.2.1) through the analyzer’s front panel. 

10.4.11.

 

ANALOG OUTPUTS 

The analyzer comes equipped with four Analog Outputs: 

A1

, 

A2

, 

A4

 and a fourth that is 

a spare. 

A1

 and 

A2

 Outputs: The first two, 

A1

 and 

A2

 are normally set up to operate in parallel 

so  that  the  same  data can be sent to two different recording devices. While the names 
imply that one should be used for sending data to a chart recorder and the other for 
interfacing with a data logger, either can be used for both applications. 

Both of these channels output a signal that is proportional to the 

H

2

S

 concentration of 

the sample gas. The 

A1

  and 

A2

  outputs can be slaved together or set up to operated 

independently. A variety of scaling factors are available;  see  Section  4.4.4  for 
information on setting the reporting range type and scaling factors for these output 
channels 

Test Output: The third analog output, labeled 

A4

 is special. It can be set by the user (see 

Section  4.6.9) to carry  the current signal level of any one of the parameters accessible 
through the 

TEST

 menu of the unit’s software. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов