Teledyne T101 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 375

Teledyne T101 Скачать руководство пользователя страница 112

Operating Instructions

Teledyne ML – T101 Operation Manual

108

will automatically be assigned an IP address by the DHCP server (Section 4.10.6.2). This
configuration is useful for quickly getting an instrument up and running on a network.
However, for permanent Ethernet connections, a static IP address should be used. Section
4.7.6.2 below details how to configure the instrument with a static IP address.

NOTE

It is a good idea to check these settings the first time you power up your analyzer after it has been

physically connected to the LAN/Internet to make sure that the DHCP has successfully downloaded the

appropriate information from you network server(s).

If the gateway IP, instrument IP and the subnet mask are all zeroes (e.g. “0.0.0.0”), the DCHP was not

successful.

You may have to manually configure the analyzer’s Ethernet properties.

See your network administrator.

To view the LAN/Internet default configuration properties, press:

SAMPLE

ENTER SETUP PASS : 818

8 1 8

ENTR

EXIT

SETUP X.X

PRIMARY SETUP MENU

CFG DAS

RNGE

PASS CLK

MORE

EXIT

SAMPLE RANGE = 500.0 PPB

H2S

=XXX.X

< TST TST > CAL

SETUP

SETUP X.X

COMMUNICATIONS MENU

ID

INET

COM1

COM2

EXIT

SETUP X.X

SECONDARY SETUP MENU

COMM

VARS DIAG

EXIT

SETUP X.X

DHCP: ON

SET>

EDIT

EXIT

SETUP X.X

INST IP: 0.0.0.0

<SET SET>

EXIT

SETUP X.X

GATEWAY IP: 0.0.0.0

<SET SET>

EXIT

SETUP X.X

SUBNET MASK: 0.0.0.0

<SET SET>

EXIT

SETUP X.X

TCP PORT: 3000

<SET SET>

EDIT

EXIT

SETUP X.X

HOSTNAME: T101

<SET

EDIT

EXIT

EDITING

disabled

when

DHCP is

ON

From this point on,

EXIT

returns to

COMMUNICATIONS

MENU

Do not alter

unless

directed to by

Teledyne

API’s

Customer

Service

personnel

«
...
110
111
112
113
114
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов