manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 178 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 178

Calibration Procedures  

Teledyne  ML  – T101 Operation Manual 

174 

  

6.6.

 

MANUAL CALIBRATION CHECKS WITH IZS OR 

ZERO/SPAN VALVES 

Zero and span checks using the zero/span valve or IZS option are similar to that described 
in Section 6.3, except: 

On units with an IZS option installed, zero air and span gas are supplied to the analyzer 
through the zero gas inlet and from ambient air. 

On units with a zero/span valve option installed, zero air and span gas are supplied to the 
analyzer through  the zero gas and span gas inlets from two different sources. 

The zero and calibration operations are initiated directly and independently with 
dedicated buttons CALZ and CALS. 

To perform a manual calibration check of an analyzer with a zero/span valve or IZS 
Option installed,  use the following  method: 

NOTE 

The instrument  can only be fitted with one type of permeation tube at a time.  Therefore the IZS option can 

only be used to calibrate or check the instrument for one gas, H

2

S or SO

2

, but not both. (SO

2

 permeation 

tubes differ from H

2

S tubes and can be purchased directly from a manufacturer). 

 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов