Teledyne T101 Скачать руководство пользователя страница 113

Страница: 113 / 375

Teledyne ML – T101 Operation Manual

Operating Instructions

109

4.7.6.2.

Manually Configuring the Ethernet with Static IP Addresses

1. Connect a cable from the analyzer’s Ethernet port to a Local Area Network

(LAN) or Internet port.

2. Access Ethernet configuration through: SETUP>MORE>COMM>INET.

3. Follow the setup sequence as shown in the illustrations that follow, and

edit the Instrument and Gateway IP addresses and Subnet Mask to the

desired settings. (From the computer, enter the same information through

an application such as HyperTerminal).

Table 4-17. LAN/Internet Default Configuration Properties

PROPERTY

DEFAULT STATE

DESCRIPTION

DHCP

This displays whether the DHCP is turned ON or

OFF. Press EDIT and toggle ON for automatic

configuration after first consulting network

administrator.

INSTRUMENT IP

ADDRESS

0.0.0.0

This string of four packets of 1 to 3 numbers each

(e.g. 192.168.76.55.) is the address of the

analyzer itself.

GATEWAY IP

ADDRESS

0.0.0.0

Can only be edited when DHCP is set to OFF.
A string of numbers very similar to the Instrument

IP address (e.g. 192.168.76.1.) that is the address

of the computer used by your LAN to access the

Internet.

SUBNET MASK

0.0.0.0

Can only be edited when DHCP is set to OFF.
Also a string of four packets of 1 to 3 numbers each

(e.g. 255.255.252.0) that identifies the LAN to

which the device is connected.
All addressable devices and computers on a LAN

must have the same subnet mask. Any

transmissions sent to devices with different subnets

are assumed to be outside of the LAN and are

routed through the gateway computer onto the

Internet.

TCP PORT

3000

This number defines the terminal control port by

which the instrument is addressed by terminal

emulation software, such as Internet or Teledyne

ML’s APICOM.

HOST NAME

T101

The name by which your analyzer will appear when

addressed from other computers on the LAN or via

the Internet. To change, see Section 4.7.6.3.

Do not change the setting for this property unless instructed to by Teledyne ML’s Technical

Support personnel.

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 113 / 375

Результаты поиска

Содержание T101

Отзывы: