manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 66 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 66

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

62 

  

To view and clear warning  messages: 

 

 

SAMPLE 

    HVPS  WARNING                    H2S = 0.00 

 

  TEST

             CAL 

 

      MSG

      

CLR

     

SETUP

 

Make sure warning messages are 

not due to  real problems. 

Press 

CLR

 to clear the current 

message. 

If more than one warning is active, the 

next message will take its place 

Once the last warning has been 

cleared, the analyzer returns to 

SAMPLE

 mode 

 

SAMPLE 

       

RANGE=500.000 PPB

        H2S =  0.00 

 
 < TST  TST >  CAL 

 

       

MSG

      

CLR

     

SETUP

 

SAMPLE 

         

 

HVPS  WARNING

           

  H2S =  0.00 

 
  TEST             CAL 

 

       MSG

      

CLR

     

SETUP

 

TEST 

deactivates warning 

messages 

 

MSG 

activates warning 

messages.   

<TST  TST

> replaced with 

TEST

  

NOTE: 

If the warning message persists 

after several attempts to clear it, 

the message may indicate a  

real problem and not an artifact 

of the warm-up period 

 

Figure 4-2. Viewing and Clearing T101 WARNING Messages 

 

4.3.

 

CALIBRATION MODE 

Pressing the CAL button  switches the T101  into multi-point calibration mode. In this 
mode, the user can calibrate the instrument or check the instrument’s calibration with the 
use of calibrated zero or span gases. 

If the instrument includes either the zero/span valve option or IZS option, the display will 
also include 

CALZ

  and 

CALS

  buttons. Pressing either of these buttons    also puts the 

instrument into multipoint  calibration mode. 

•

 

The CALZ button is used to initiate a calibration  of the zero point. 

•

 

The CALS button is used to calibrate the span point of the analyzer.  It is 

recommended  that this span calibration is performed  at 90% of full scale 

of the analyzer’s  currently selected reporting  range. 

Because  of  their  critical  importance  and complexity, calibration operations are described 
in Section 6 of this manual.   

4.3.1.

 

CALIBRATION PASSWORD SECURITY 

The  T101  calibration functions may be password protected for to prevent inadvertent 
adjustments.  When the calibration password has been enabled using the 

PASS 

menu item 

found under the Setup Menu (Section  4.4.5), the system will prompt the user for a 
password anytime 

CAL

, 

CALZ

, 

CALS 

activated. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов