manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 167 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 167

Teledyne ML – T101 Operation Manual 

Calibration Procedures 

 

163 

6.

 

CALIBRATION PROCEDURES 

This  Section  describes the calibration procedures for the T101. All of the methods 
described in this section can be initiated and controlled  through  the COM ports. 

NOTE 

If you are using the T101  for US-EPA controlled monitoring of SO

2

, see Section 8 for 

information  on the EPA calibration  protocol. 

6.1.

 

CALIBRATION PREPARATIONS 

The calibration procedures in this section assume that the analog output reporting range 
and units of measure, reporting range mode, and reporting range span have already been 
selected for the analyzer. If this has not been done, please do so before continuing 
(Section 4.4.4 for instructions). 

Also, unless otherwise stated, the procedures in this Section  are written with the 
assumption that the T101  is being used in its default configuration as an H

2

S analyzer.  

The same methods and setups can be followed when the instrument is configured for SO

2

 

measurement by substituting SO

2

 span gas for the H2S span gas listed in the procedure. 

For analyzers configured in H

2

S 

 SO

2

 multigas mode, see Section 6.8 

NOTE 

In applications where the instrument may be used to measure SO

2

 as well  as H

2

S make 

sure that the calibration gas being used matches the gas measurement mode in which 

the instrument is set during the calibration  procedure. 

6.1.1.

 

REQUIRED EQUIPMENT, SUPPLIES, AND EXPENDABLES 

Calibration of the Model T101  analyzer requires a certain amount of equipment and 
supplies. These include,  but are not limited  to, the following: 

•

 

Zero-air source 

•

 

Hydrogen  sulfide  span gas source 

•

 

Gas lines - all gas line materials  should be Teflon-type or  glass. 

•

 

A recording device such as a strip-chart recorder and/or data logger 

(optional). 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов