manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 182 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 182

Calibration Procedures  

Teledyne  ML  – T101 Operation Manual 

178 

  

If contact closures are used in conjunction with the analyzer’s AutoCal (Section 6.9) 
feature and the AutoCal attribute CALIBRATE is enabled, the T101 will not re-calibrate 
the analyzer until the contact is opened. At this point, the new calibration values will be 
recorded before the instrument returns to SAMPLE mode. 

If the AutoCal attribute CALIBRATE is disabled, the instrument will return to SAMPLE 
mode, leaving the instrument’s internal calibration variables unchanged. 

6.8.

 

MANUAL CALIBRATION IN MULTIGAS 

MEASUREMENT MODE 

If the analyzer is being operated in multigas measurement mode, the methods and setups 
for performing calibrations are identical to those defined in Sections 6.2 and 6.4 with the 
two exceptions  

Some provision must be made for supplying both types of calibrated span gas to the 
analyzer.  A typical setup for this might  be: 

 

No Valve Options Installed

 

Chassis

 

Sample

 

Zero Air 

Exhaust

 

Span

 

MODEL 701

 

Zero Air 

Generator

 

 

Calibrated 

H

2

S GAS 

(At high 

concentration)

 

Source of

 

SAMPLE Gas 

Removed

 

during 

Calibration

 

 

MODEL T700 Gas 

Dilution 

Calibrator  

(with Ozone Bench 

Option)

 

Calibrated 

SO

2

 GAS 

(At high 

concentration)

 

 

Figure 6-4. Typical Setup for Manual Calibratio in Multigas Measurement Mode 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов