Teledyne T101 Скачать руководство пользователя страница 25

Страница: 25 / 375

Teledyne ML – T101 Operation Manual

Introduction

Option

Number

Description/Notes

Current Loop Analog

Outputs

Adds isolated, voltage-to-current conversion circuitry to the

analyzer’s analog outputs.

Isolated 0-20 or 4-20 mA current output (up to three can be retrofitted if not

installed at the factory)

Parts Kits

42A

Expendables Kit with IZS includes the items needed to refurbish the

internal zero air scrubber (IZS) that is included.

Spare Parts Kit includes spares parts for one unit.

NO Optical Filter

Recommended for High NOX backgrounds.

47B

Required for EN Certification.

Calibration Valves

Used to control the flow of calibration gases generated from external

sources, rather than manually switching the rear panel pneumatic

connections.

50A

Ambient Zero and Ambient Span

50G

Zero Scrubber and Internal Span Source (IZS)

S Permeation Tubes Replacement tubes for the IZS option; identical size/shape; different

effusion rates.

Effusion Rate
(@ 50°C)

Approximate

Concentration

Specified Flow Rate (of indicated perm

tube rate)

(uncertified) 52A

106 ng/min

.08 -.12 ppm

0.76 lpm (nominal) ± 25%

(certified) 52E

76 ng/min

.04 - .06 ppm 0.76 lpm ± 5%

Communication Cables

For remote serial, network and Internet communication with the

analyzer.

Type

Description

60A

RS-232

Shielded, straight-through DB-9F to DB-25M cable, about 1.8 m

long. Used to interface with older computers or code activated

switches with DB-25 serial connectors.

60B

RS-232

Shielded, straight-through DB-9F to DB-9F cable of about 1.8 m

length.

60C

Ethernet Patch cable, 2 meters long, used for Internet and LAN

communications.

60D

USB

Cable for direct connection between instrument (rear panel USB

port) and personal computer.

Concentration Alarm

Relay

Issues warning when gas concentration exceeds limits set by user.

Four (4) “dry contact” relays on the rear panel of the instrument. This relay

option is different from and in addition to the “Contact Closures” that come

standard on all TML instruments.

RS-232 Multidrop

Enables communications between host computer and up to eight

analyzers.

Multidrop card seated on the analyzer’s CPU card.
Each instrument in the multidrop network requires this card and a

communications cable (Option 60B).

Special Features

Built in features, software activated

N/A

Maintenance Mode Switch, located inside the instrument, places the

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 25 / 375

Результаты поиска

Содержание T101

Отзывы: