manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 30 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 30

Getting Started 

Teledyne  ML  – T101 Operation Manual 

26 

  

4.

 

Inspect the interior  of the instrument  to make  sure all  circuit boards  and 

other components are in good shape and properly seated.  

5.

 

Check the connectors of the various internal  wiring  harnesses and 

pneumatic  hoses to make  sure  they are  firmly  and properly  seated. 

6.

 

Verify that all of the optional hardware ordered with the unit has been 

installed. These are checked on the paperwork  (Form  04551) 

accompanying  the analyzer. 

 

7.

 

VENTILATION CLEARANCE:  Whether the analyzer is set up on a bench 

or installed  into an instrument  rack, be sure to leave sufficient ventilation 

clearance. 

AREA 

MINIMUM REQUIRED CLEARANCE 

Back of the instrument 

10 cm / 4 inches 

Sides of the instrument 

2.5 cm / 1 inch 

Above and below the instrument. 

2.5 cm / 1 inch 

Various rack mount kits are available for this analyzer.  

3.2.

 

INSTRUMENT LAYOUT 

Instrument layout includes front panel and display, rear panel connectors, and internal 
chassis layout. 

3.2.1.

 

FRONT PANEL 

Figure  3-1  shows the analyzer’s front panel layout, followed by a close-up of the display 
screen in Figure  3-2, which is described in Table  3-1. The two USB ports on the front 
panel are provided for the connection of peripheral devices: 

•  Plug-in mouse  (not included) to be used  as an  alternative to the 

touchscreen interface 

•  Thumb  drive (not included) to download  updates to instruction software 

(contact TML Technical Support  for information). 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов