manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 52 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 52

Getting Started 

Teledyne  ML  – T101 Operation Manual 

48 

  

Temperature  of  the  H

2

S

: Increasing the temperature of the increases the pressure inside 

the tube and therefore increases the effusion rate. 

Flow rate of the zero air

: If the previous two variables are constant, the permeation rate 

of the calibration gas into the zero air stream will be constant. Therefore, a lower flow 
rate of zero air produces higher concentrations of H

2

S. The T101 usually has a constant 

flow rate and a constant permeation rate; hence, variations in concentration can be 
achieved by changing  the IZS temperature. 

NOTE 

The permeation tube is not included in the IZS Option and must be ordered separately.  

Permeation Tube Heater 

In order to keep the permeation rate constant, the IZS enclosure is heated to a constant 
50° C (10° above the maximum operating temperature of the instrument). The IZS heater 
is controlled by a precise PID (Proportional/Integral/Derivative) temperature control loop. 
A thermistor measures the actual temperature and reports it to the CPU for control 
feedback. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов