Teledyne T101 Скачать руководство пользователя страница 90

Страница: 90 / 375

Operating Instructions

Teledyne ML – T101 Operation Manual

The following DC current output limits apply to the current loop modules:

Table 4-11. Analog Output Current Loop Range

RANGE

MINIMUM OUTPUT

MAXIMUM OUTPUT

0-20 mA

0 mA

20 mA

These are the physical limits of the current loop modules, typical applications use 2-20 or 4-20

mA for the lower and upper limits. Please specify desired range when ordering this option.
The default offset for all ranges is 0 mA.

Pin assignments for the output connector at the rear panel of the instrument are shown in
Table 4-12.

ANALOG OUT

A1 A2 A3 A4

+ - + - + - + -

Table 4-12. Analog Output Pin Assignments

PIN

ANALOG

OUTPUT

VOLTAGE

SIGNAL

CURRENT

SIGNAL

V Out

I Out +

Ground

I Out -

V Out

I Out +

Ground

I Out -

Not Used

V Out

not available

Ground

not available

See Figure 3-4 for the location of the analog output connector on the instrument’s rear
panel.

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 90 / 375

Результаты поиска

Содержание T101

Отзывы: