manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 74 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 74

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

70 

  

4.4.4.5.

 

Independent Range Mode (IND) 

Selecting independent range mode allows the 

A1

  and 

A2

  outputs to be configured with 

different  measurement  ranges.  The  analyzer software calls these two ranges 

LOW

 and 

HIGH

.  The 

LOW

  range setting corresponds with the analog output labeled 

A1

 on the 

rear panel of the instrument.  The 

HIGH

 range setting corresponds with the 

A2

 output.  

While the software names these two ranges

  LOW

  and 

HIGH

, they do not have to be 

configured that way. 

Also, in this mode the 

RANGE 

Test function displayed on the front panel during

 

SAMPLE

 mode will be replaced by two separate functions, 

RANGE1

 & 

RANGE2

.  

•

 

LOW range = RANGE1  =  Range  value for output A1 = 0-1500 ppb 

H

2

S. 

•

 

HIGH  range = RANGE2  = Range value for output A2 = 0-500 ppb 

H

2

S. 

For T101’s configured  to measure both SO

2

 and H

2

S in multigas measurement mode:  

•

 

LOW range = RANGE1  =  Range  value for output A1= 0-1500 ppm 

SO

2

. 

•

 

HIGH  range = RANGE2  = Range value for output A2 =0-1000 ppm 

H

2

S. 

To select the independent reporting range mode and set the upper measurement limits for 
the two outputs, press:

 

 
 

 

 
 

SAMPLE          

ENTER SETUP PASS : 818

 

 

        

 8        1        8 

 

                      

ENTR

  

 EXIT

 

 

 

 

SETUP X.X 

 

    

PRIMARY SETUP MENU

 

  

 

 CFG  DAS

  

RNGE

  

PASS  CLK  MORE  

EXIT

 

 

 

 

SETUP X.X          

RANGE CONTROL MENU

 

 

 

 

 

MODE

 

 

 

 

 

 

SET  UNIT

 

 

 

 

EXIT

 

 

 

 

SETUP X.X 

RANGE MODE: 

SNGL

 

 

 

 

 SNGL  

IND

 AUTO    

 

     ENTR  EXIT

 

 

 

 

SETUP X.X 

RANGE CONTROL MENU

 

 

 

 

 MODE

 

 

 

 

 

 

SET

  UNIT

 

 

 

 

EXIT

 

 

 

 

SETUP X.X

 

HIGH RANGE:

 

500.0 Conc

 

 

 

 

 0          0         5         

 

0          0          .0

       

ENTR

   EXIT

 

 

 

 

SETUP X.X 

LOW RANGE

: 

500.0 Conc

 

 

 

 

 0          0      

  

 1

         

0          0          .0

       

ENTR

   EXIT

 

 

 

 

SETUP X.X        

RANGE CONTROL MENU 

 

 

 

 MODE

 

 

 

 

 

 

SET  UNIT

 

 

 

 

EXIT 

EXIT

 Returns 

to the Main 

SAMPLE

 Display 

 

 

 

SETUP X.X 

RANGE MODE: 

DUAL

 

 

 

 

 SNGL

 

 

 

 

 

 

IND  AUTO   

 

     ENTR

  EXIT

 

Toggle the 

buttons under 

each digit to set 

the upper limit 

of each range. 

 SAMPLE           RANGE = 500.0 PPB           

H2S 

=XXX.X  

 

 < TST  TST >  CAL  

 

 

SETUP

 

 

NOTE 

In INDEPENDENT  range mode the two reporting  ranges have separate slopes and offsets 

for computing concentration and MUST  be independently  calibrated. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов