Teledyne T101 Скачать руководство пользователя страница 98

Страница: 98 / 375

Operating Instructions

Teledyne ML – T101 Operation Manual

To adjust the zero and span values of the current outputs, activate the ANALOG I/O
CONFIGURATION MENU (see Section 4.6.3), then press

DIAG AIO

CONC_OUT_2 SPAN: 5000 mV

U100 UP10

UP DOWN DN10

D100

ENTR EXIT

DIAG AIO

AUTO CALIBRATING CONC_OUT_2

DIAG AIO

AIN CALIBRATED:

SET>

EDIT

EXIT

DIAG

ANALOG I / O CONFIGURATION

ENTR

EXIT

FROM ANALOG I/O CONFIGURATION MENU

DIAG AIO

CONC_OUT_2 RANGE: CURR

<SET

SET>

EDIT

EXIT

DIAG AIO

CONC_OUT_2 CALIBRATED: NO

< SET

CAL

EXIT

DIAG AIO

CONC_OUT_2:CURR, NO CAL

< SET SET>

EDIT

EXIT

Press

SET>

to select the analog output channel

to be configured:.

Increase or decrease the current

output by 100, 10 or 1 counts.

The resulting change in output

voltage is displayed in the upper

line.

Continue adjustments until the

correct current is measured with

the current meter.

DIAG AIO

CONC_OUT_2 ZERO: 27 mV

U100 UP10

UP DOWN DN10 D100

ENTR EXIT

EXIT

ignores the

new setting,

ENTR

accepts the new

setting.

DIAG AIO

CONC_OUT_2 CALIBRATED: YES

< SET

CAL

EXIT

DIAG AIO

CONC_OUT_2 ZERO: 4921 mV

U100 UP10

UP DOWN DN10 D100

ENTR EXIT

DIAG AIO

CONC_OUT_2 CURR-Z: 0 mV

U100

UP10

UP DOWN DN10 D100

ENTR EXIT

The instrument attempt to automatically calibrate

the channel … then beep.

If a current meter is not available, an alternative method for calibrating the current loop
outputs is to connect a 250

Ω

1% resistor across the current loop output. Using a

voltmeter, connected across the resistor, follow the procedure above but adjust the output
to the following values:

Table 4-14. Current Loop Output Calibration with Resistor

FULL

SCALE

VOLTAGE FOR 2-20 MA

(measured across resistor)

VOLTAGE FOR 4-20 MA

(measured across resistor)

0.5 V

1.0 V

100%

5.0 V

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 98 / 375

Результаты поиска

Содержание T101

Отзывы: