manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 9 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 9

 

 

v 

WARRANTY 

WARRANTY POLICY (02024  F) 

Teledyne  Monitor Labs  (TML), a business unit of Teledyne Instruments, Inc., 
provides that: 

Prior to shipment, TML  equipment is thoroughly inspected and tested.  Should 
equipment failure occur, TML assures its customers that prompt service and support 
will be available. 

COVERAGE 

After the warranty period and throughout the equipment lifetime, TML stands ready 
to provide on-site or in-plant service at reasonable rates similar to those of other 
manufacturers in the industry.  All maintenance and the first level of field 
troubleshooting are to be performed by the customer. 

NON-TML  MANUFACTURED EQUIPMENT 

Equipment provided but not manufactured by TML is warranted and will be repaired 
to the extent and according to the current terms and conditions of the respective 
equipment manufacturer’s warranty. 

Product Return 

All units or components returned to Teledyne ML should be properly packed for 
handling and returned freight prepaid to the nearest designated Service Center. 
After the repair, the equipment will  be returned, freight prepaid. 
 
 
The complete Terms and Conditions of Sale can be reviewed at 

http://www.teledyne-ml.com/terms_and_conditions.asp

 

 

 

 

 

CAUTION  – Avoid Warranty Invalidation 

Failure to comply with proper anti-Electro-Static Discharge (ESD) handling and packing 

instructions and Return Merchandise Authorization (RMA) procedures when returning 

parts for repair or calibration may void your warranty. For anti-ESD handling and 

packing instructions please refer to “Packing Components for Return to Teledyne ML” in 

the  Primer on Electro-Static Discharge section of this manual, and for RMA procedures 

please refer to our Website at 

http://www.teledyne-ml.com

 under Customer Support > 

Return Authorization. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов