manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 229 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 229

Teledyne ML - T101 Operation Manual 

Troubleshooting  & Service

 

 

225 

•

 

Sample  vent line is located too far from  the instrument’s sample inlet 

and causes long mixing  and purge times. Locate sample inlet (overflow) 

vent as close as possible to the analyzer’s  sample  inlet port. 

•

 

Dirty sample  chamber. Clean the sample  chamber. 

•

 

Insufficient time allowed for purging  of lines upstream of the analyzer. 

•

 

Insufficient time allowed for H

2

S calibration gas source to become stable. 

 

9.4.3.

 

THE ANALYZER DOESN’T APPEAR ON THE LAN OR 

INTERNET 

Most problems related to Internet communications via the Ethernet will be due to 
problems external to the analyzer (e.g. bad network wiring or connections, failed routers, 
malfunctioning servers, etc.).  However,  there are several symptoms that indicate the 
problem  may be with the Ethernet card itself. 

If  neither of the Ethernet cable’s two status LED’s (located on the back of the cable 
connector) is lit  while the instrument is connected to a network: 

•  Verify that the instrument is being connected to an active network jack. 

•  Check the internal cable connection between the Ethernet card and  the 

CPU board. 

9.5.

 

SUBSYSTEM CHECKOUT 

The preceding sections of this manual discussed a variety of methods for identifying 
possible sources of failures or performance problems within the analyzer. In most cases 
this included a list of possible causes and, in some cases, quick solutions or at least a 
pointer to the appropriate sections describing them. This section describes how to 
determine if a certain component or subsystem is actually the cause of the problem being 
investigated. 

9.5.1.

 

DETAILED PRESSURE LEAK CHECK 

Obtain a leak checker similar to Teledyne ML’s part number 01960, which contains a 
small pump, shut-off valve, and pressure gauge to create both over-pressure and 
vacuum. Alternatively, a tank of pressurized gas, with the two stage regulator adjusted to 

≤ 15 psi,  a shutoff valve and pressure gauge may be used. 

CAUTION 

Once tube fittings  have been wetted with soap solution under a pressurized system,  do not apply or re-

apply vacuum as this  will cause soap solution to be sucked into the instrument, contaminating inside 

surfaces. 

Do not exceed 15 PSI when pressurizing the system. 

1.

 

Turn OFF power to the instrument  and remove  the instrument  cover. 

12.

 

Install a leak checker or a tank of gas (compressed, oil-free air or 

nitrogen) as described above on the sample  inlet at the rear panel. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов