Teledyne T101 Скачать руководство пользователя страница 95

Страница: 95 / 375

Teledyne ML – T101 Operation Manual

Operating Instructions

+DC Gnd

V OUT +

V OUT -

V IN +

V IN -

Recording

Device

ANALYZER

See Table 3-1 for

pin assignments

of Analog Out

connector on the

rear panel

Figure 4-4. Setup for Calibrating Analog Outputs

To make these adjustments, the

AOUT

auto-calibration feature must be turned off

(Section6.9). Activate the ANALOG I/O CONFIGURATION MENU (see Section
4.6.3), then press:

Press

SET>

to select the analog output channel to be configured:

DISPLAYED AS =

CHANNEL

CONC_OUT_1 =

CONC_OUT_2 =

TEST OUTPUT =

DIAG

ANALOG I / O CONFIGURATION

ENTR

EXIT

DIAG AIO

AOUTS CALIBRATED:

< SET

SET>

CAL

EXIT

FROM ANALOG I/O CONFIGURATION MENU

DIAG AIO

CONC_OUT_1 :5V, NO CAL

< SET SET>

EDIT

EXIT

DIAG AIO

CONC_OUT_1 CALIBRATED: YES

< SET

CAL

EXIT

DIAG AIO

CONC_OUT_1 RANGE: 5V

SET>

EDIT

EXIT

DIAG AIO

CONC_OUT_2 CALIBRATED: NO

< SET

CAL

EXIT

DIAG AIO

CONC_OUT_1 VOLT–Z : 0 mV

U100 UP10 UP DOWN DN10 D100

ENTR EXIT

Toggle to increase / decrease the analog output

by 100, 10 or 1 counts.

Continue adjustments until the voltage measured

at the output of the analyzer and/or the input of

the recording device matches the value in the

upper right hand corner of the display to the

tolerance specified.

The concentration display

will not change. Only

the voltage reading of your voltmeter will change.

DIAG AIO

CONC_OUT_1 VOLT–S : 4500 mV

U100 UP10 UP DOWN DN10 D100

ENTR EXIT

DIAG AIO

CONC_OUT_1 REC OFS: 0 mV

< SET

SET>

EDIT

EXIT

If AutoCal is ON, go to

Section 6.7.3

EXIT

ignores the

new setting.

ENTR

accepts the

new setting.

DIAG AIO

CONC_OUT_1 AUTO CAL: OFF

< SET

SET>

EDIT

EXIT

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 95 / 375

Результаты поиска

Содержание T101

Отзывы: