Teledyne T101 Скачать руководство пользователя страница 115

Страница: 115 / 375

Teledyne ML – T101 Operation Manual

Operating Instructions

111

Configure the

INSTRUMENT IP

GATEWAY IP

and

SUBNET MASK

addresses:

Internet Configuration Touchscreen Functions

BUTTON

FUNCTION

[0]

Press to cycle through the range of numerals and
available characters (“

0 – 9”

“ . ”

)

<CH CH>

Moves the cursor one character left or right.

DEL

Deletes a character at the cursor location.

ENTR

Accepts the new setting and returns to the previous
menu.

EXIT

Ignores the new setting and returns to the previous
menu.

Buttons appear only as applicable.

SETUP X.X

DHCP: OFF

SET>

EDIT

EXIT

SETUP X.X

INST IP: 000.000.000.000

<SET SET> EDIT

EXIT

SETUP X.X

GATEWAY IP: 000.000.000.000

<SET SET> EDIT

EXIT

SETUP X.X

INST IP: [0] 00.000.000

<CH CH> DEL [0]

ENTR EXIT

SETUP X.X

SUBNET MASK:255.255.255.0

<SET SET> EDIT

EXIT

SETUP X.X

SUBNET MASK:[2]55.255.255.0

<CH CH> DEL [?]

ENTR EXIT

SETUP X.X

TCP PORT 3000

<SET

EDIT

EXIT

The PORT number needs to remain at

3000

Do not change this setting unless instructed to by

Teledyne API’s Customer Service personnel.

(Continued from preceding illustration)

SETUP X.X

GATEWAY IP: [0] 00.000.000

<CH CH> DEL [?]

ENTR EXIT

Cursor

location is

indicated by

brackets

SETUP X.X

INITIALIZING INET 0%

…

INITIALIZING INET 100%

SETUP X.X

INITIALIZATI0N SUCCEEDED

SETUP X.X

INITIALIZATION FAILED

SETUP X.X

COMMUNICATIONS MENU

INET

COM1

COM2

EXIT

Pressing

EXIT

from

any of the above

display menus

ignores any changes

made.

Contact your IT

Network Administrator

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 115 / 375

Результаты поиска

Содержание T101

Отзывы: