Teledyne T101 Скачать руководство пользователя страница 233 | Manualshive

Страница: 233 / 375

Teledyne T101 Скачать руководство пользователя страница 233

Teledyne ML - T101 Operation Manual

Troubleshooting & Service

229

does not turn on/off, then the associated device (valve or heater) or its control device
(valve driver, heater relay) is malfunctioning.

Several of the control devices are in sockets and can easily be replaced. The table below
lists the control device associated with a particular function:

Table 9-6. Relay Board Control Devices

FUNCTION

CONTROL DEVICE

SOCKETED

Valve0 – Valve3

U5

Yes

Valve4 – Valve7

U6

Yes

All heaters

K1-K5

Yes

9.5.9.

MOTHERBOARD

9.5.9.1.

A/D functions

A basic check of the analog to digital (A/D) converter operation on the motherboard is
to use the

Signal I/O

function under the

DIAG

menu. Check the following two A/D

reference voltages and input signals that can be easily measured with a voltmeter.

•

Using the Signal I/O function (Section 4.6.1 and Appendix D), view the

value of REF_4096_MV and REF_GND. If these signals are within 10

mV and 3 mV, respectively, of their nominal values (4096 and 0) and are

stable to within ±0.5 mV, the basic A/D converter is functioning properly.

If these values fluctuate largely or are off by more than specified above,

one or more of the analog circuits may be overloaded or the

motherboard may be faulty.

•

Choose one parameter in the Signal I/O function such as

SAMPLE_PRESSURE (see previous section on how to measure it).

Compare its actual voltage with the voltage displayed through the

SIGNAL I/O function. If the wiring is intact but there is a difference of

more than ±10 mV between the measured and displayed voltage, the

motherboard may be faulty.

9.5.9.2.

Analog Output Voltages

To verify that the analog outputs are working properly, connect a voltmeter to the output
in question and perform an analog output step test as described in Section 4.6.2.

For each of the steps, taking into account any offset that may have been programmed
into the channel (Section 4.6.3.4), the output should be within 1% of the nominal value
listed in the table below except for the 0% step, which should be within 2-3 mV. If one
or more of the steps is outside of this range, a failure of one or both D/A converters and
their associated circuitry on the motherboard is likely.

Table 9-7. Analog Output Test Function - Nominal Values

FULL SCALE OUTPUT VOLTAGE

100MV

1V

5V

10V

STEP

%

NOMINAL OUTPUT VOLTAGE

1

0

0 mV

0

0

0

2

20

20 mV

0.2

1

2

«
...
231
232
233
234
235
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов