Teledyne T101 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 375

Teledyne T101 Скачать руководство пользователя страница 96

Operating Instructions

Teledyne ML – T101 Operation Manual

92

4.6.3.4.

Analog Output Offset Adjustment

Some analog signal recorders require that the zero signal is significantly different from
the baseline of the recorder in order to record slightly negative readings from noise
around the zero point. This can be achieved in the T101 by defining a zero offset, a small
voltage (e.g., 10% of span), which can be added to the signal of individual output
channels by activating the ANALOG I/O CONFIGURATION MENU (see Section 4.6.3),
then pressing:

DIAG AIO

RECORD OFFSET: 0 MV

+ 0 0 0 0

ENTR EXIT

DIAG

ANALOG I / O CONFIGURATION

PREV

NEXT

ENTR

EXIT

DIAG AIO

AOUTS CALIBRATED:

NO

< SET

SET>

CAL

EXIT

FROM ANALOG I/O CONFIGURATION MENU

DIAG AIO

CONC_OUT_2 RANGE: 5V

SET>

EDIT

EXIT

Set the recorder

offset (in mV) of

the selected

channel

DIAG AIO

CONC_OUT_2:5V, CAL

< SET SET>

EDIT

EXIT

DIAG AIO

CONC_OUT_2 REC OFS: 0 mV

< SET

SET>

EDIT

EXIT

Pressing

ENTR

accepts the

new setting and returns to the

previous menu.

Pressing

EXIT

ignores the new

setting and returns to the

previous menu.

Press

SET>

to select the

analog output channel to
be configured. Then press

EDIT

to continue

4.6.3.5.

Current Loop Output Adjustment

A current loop option is available and can be installed as a retrofit for each of the analog
outputs of the analyzer. This option converts the DC voltage analog output to a current
signal with 0-20 mA output current. The outputs can be scaled to any set of limits within
that 0-20 mA range. However, most current loop applications call for either 2-20 mA or
4-20 mA range. All current loop outputs have a +5% over-range. Ranges with the lower
limit set to more than 1 mA (e.g., 2-20 or 4-20 mA) also have a -5% under-range.

To switch an analog output from voltage to current loop after installing the current output
printed circuit assembly, follow the instructions in Section 4.6.3.1 and select curr from the
list of options on the “Output Range” menu.

Adjusting the signal zero and span values of the current loop output is done by raising or
lowering the voltage of the respective analog output. This proportionally raises or lowers
the current produced by the current loop option.

«
...
94
95
96
97
98
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов