manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 120 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 120

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

116 

  

After connecting a USB cable between your PC and the instrument, ensure their baud 
rates match (change the baud rate setting for either your PC’s software or the instrument). 
The baud rate setting is in the Communications Menu under COM2, which is the default 
setup menu for USB configuration. 

Also, while there are various communication modes available (Table 4-18), the default 
settings are recommended for USB, except to change the baud rate if required.. 

4.7.8.

 

MULTIDROP RS-232 SET UP 

When the RS-232 Multidrop option is installed, connection adjustments and configuration 
through the menu system are required. This section provides instructions for the internal 
connection adjustments, then for external connections, and ends with instructions for 
menu-driven configuration. 

NOTE 

Because the RS-232 Multidrop option uses both the RS232 and COM2 DB9 connectors  on the analyzer’s 

rear panel to connect the chain of instruments, COM2 port is no longer available for separate RS-232 or 

RS-485 operation. 

 

CAUTION 

Printed Circuit  Assemblies  (PCAs)  are sensitive to electro-static  discharges  too small to be felt by the 

human nervous system.   Failure to use ESD protection when working with electronic assemblies will void 

the instrument warranty.  Refer to Section 13 for more information on preventing ESD  damage. 

In each instrument with the Multidrop option there is a shunt jumpering two pins on the 
serial Multidrop and LVDS printed circuit assembly (PCA), as shown in Figure 4-9. This 
shunt must be removed from all instruments except that designated as last in the 
multidrop chain, which must remain terminated. This requires powering off and opening 
each instrument and making  the following  adjustments: 

1.

 

With NO power  to the instrument,  remove  its top cover and lay the rear 

panel open for access to the Multidrop/LVDS  PCA, which is seated on the 

CPU. 

2.

 

On  the Multidrop/LVDS  PCA’s  JP2 connector, remove  the shunt  that 

jumpers  Pins 21 

↔

 22 as indicated in Figure 4-9. (Do this for all but the 

last instrument  in  the chain where the shunt should remain  at Pins 21 

↔

 

22). 

3.

 

Check that the following  cable connections are made  in  all instruments 

(again refer to Figure 4-9): 

•

 

J3 on the Multidrop/LVDS  PCA to the CPU’s COM1 connector 
(Note  that the CPU’s COM2  connector is not used in Multidrop) 

•

 

J4 on the Multidrop/LVDS  PCA to J12 on the motherboard 

•

 

J1 on the Multidrop/LVDS  PCS to the front panel LCD  

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов