Teledyne T101 Скачать руководство пользователя страница 121

Страница: 121 / 375

Teledyne ML – T101 Operation Manual

Operating Instructions

117

Figure 4-9. Jumper and Cables for Multidrop Mode

Note

If you are adding an instrument to the end of a previously configured chain, remove the shunt between

Pins 21

↔

22 of JP2 on the Multidrop/LVDS PCA in the instrument that was previously the last instrument

in the chain.

Close the instrument.

Referring to Figure 4-10 use straight-through DB9 male



DB9 female

cables to interconnect the host RS232 port to the first analyzer’s RS232

port; then from the first analyzer’s COM2 port to the second analyzer’s

RS232 port; from the second analyzer’s COM2 port to the third analyzer’s

RS232 port, etc., connecting in this fashion up to eight analyzers, subject

to the distance limitations of the RS-232 standard.

On the rear panel of each analyzer, adjust the DCE DTE switch so that the

green and the red LEDs (RX and TX) of the COM1 connector (labeled

RS232) are both lit. (Ensure you are using the correct RS-232 cables

internally wired specifically for RS-232 communication; see Table 1-1,

“Communication Cables” and the preceding subsection, “RS-232

Connection”).

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 121 / 375

Результаты поиска

Содержание T101

Отзывы: