Teledyne T101 Скачать руководство пользователя страница 122

Страница: 122 / 375

Operating Instructions

Teledyne ML – T101 Operation Manual

118

Analyzer

Last Analyzer

Female DB9

Male DB9

RS-232

COM2

RS-232

COM2

RS-232

COM2

RS-232

COM2

Host

RS-232 port

Ensure jumper is

installed between

JP2 pins 21

↔

in last instrument

of multidrop chain.

Figure 4-10.Multidrop PCA Host/Analyzer Interconnect Diagram

BEFORE communicating from the host, power on the instruments and

check that the Instrument ID code is unique for each (see Section 4.7.1).
a. In the SETUP Mode menu go to SETUP>MORE>COMM>ID. The default

ID is typically the model number or “0”.

b. To change the identification number, press the button below the digit

to be changed.

c. Press/select ENTER to accept the new ID for that instrument.

Next, in the SETUP>MORE>COMM>COM1 menu (do not use the COM2

menu for multidrop), edit the COM1 MODE parameter as follows:

press/select EDIT and set only QUIET MODE, COMPUTER MODE, and

MULTIDROP MODE to ON. Do not change any other settings.

Press/select ENTER to accept the changed settings, and ensure that COM1

MODE now shows 35.

10.

Press/select SET> to go to the COM1 BAUD RATE menu and ensure it

reads the same for all instruments (edit as needed so that all instruments

are set at the same baud rate).

Note

Teledyne ML recommends setting up the first link between the Host and the first analyzer and testing it

before setting up the rest of the chain.

The (communication) Host instrument can address only one instrument at a time, each by its unique ID

(see step 7 above).

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 122 / 375

Результаты поиска

Содержание T101

Отзывы: