manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 107 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 107

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

103 

Once a TEST function is selected, the instrument  begins to report a signal on the 

A4

 

output and adds 

TEST=

  to the list of test functions viewable on the display (just before 

the TIME display). 

4.7.

 

SETUP – COMM: SETTING UP THE ANALYSER’S 

COMMUNICATION PORTS 

For remote operation the T101  is equipped with an Ethernet port, a USB port and two 
serial communication (com) ports located on the rear panel.  Both com ports (labeled 
RS232, which is the COM1  port  and  COM2) operate similarly and give the user the 
ability to communicate with, issue commands to, and receive  data from the analyzer 
through an external computer system or terminal. By default, both ports operate on the 
RS-232 protocol.   

The  RS232  port can also be configured to operate in single or RS-232 Multidrop mode 
(Option 62).  The COM2 port can be left in its default configuration for standard RS-232 
operation, or reconfigured for half-duplex RS-485 operation; (contact the factory for 
configuration information). When COM2  is configured for RS-485 communication, the 
rear panel USB port is disabled. 

A code-activated switch (CAS), can also be used on either port to connect typically 
between 2 and 16 send/receive instruments (host computer(s) printers, data loggers, 
analyzers, monitors, calibrators, etc.) into one communications hub. Contact Teledyne 
ML’s Sales for more information on CAS systems. 

4.7.1.

 

INSTRUMENT ID 

Each type of Teledyne ML analyzer is configured with a default ID code.  The default ID 
code for all T101 analyzers is either “

0

” or 

101

.  The ID number is only important if more 

than one analyzer is connected to the same communications channel such as when several 
analyzers are on the same Ethernet LAN, in an RS-232 Multidrop chain, or operating over 
a RS-485 network.  If two analyzers of the same model type are used on one channel, the 
ID codes of one or both of the instruments needs to be changed so that they are unique to 
the instruments.    

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов