Teledyne T101 Скачать руководство пользователя страница 311

Страница: 311 / 375

Teledyne API T/E-Series Models 101, 102, and 108 Software Documentation (PN05492D DCN6485)

A-17

Setup Variable

Numeric

Units

Default

Value

Value Range

Description

BAUD_RATE2 —

19200

300,
1200,
2400,
4800,
9600,
19200,
38400,
57600,
115200

RS-232 COM2 baud rate.

Enclose value in double

quotes (“) when setting from

the RS-232 interface.

MODEM_INIT2

—

“AT Y0 &D0

&H0 &I0

S0=2 &B0

&N6 &M0 E0

Q1 &W0”

Any

character in

the allowed

character

set. Up to

100

characters

long.

RS-232 COM2 modem

initialization string. Sent

verbatim plus carriage return

to modem on power up or

manually. Enclose value in

double quotes (“) when

setting from the RS-232

interface.

RS232_PASS

Password

940331

0–999999

RS-232 log on password.

MACHINE_ID ID

101

102

108

0–9999

Unique ID number for

instrument.

COMMAND_PROMPT — “Cmd>

”

Any

character in

the allowed

character

set. Up to

100

characters

long.

RS-232 interface command

prompt. Displayed only if

enabled with RS232_MODE

variable. Enclose value in

double quotes (“) when

setting from the RS-232

interface.

TEST_CHAN_ID —

NONE

NONE,
PMT

READING,
UV

READING,
OXY FLOW

SAMPLE

FLOW,
SAMPLE

PRESSURE,
RCELL

TEMP,
CHASSIS

TEMP,
IZS TEMP,
PMT TEMP,
CONV TEMP

HVPS

VOLTAGE

Diagnostic analog output ID.

Enclose value in double

quotes (“) when setting from

the RS-232 interface.

07266B DCN6485

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 311 / 375

Результаты поиска

Содержание T101

Отзывы: