manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 32 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 32

Getting Started 

Teledyne  ML  – T101 Operation Manual 

28 

  

 

e front panel liquid crystal display screen includes touch control. Upon analyzer start-up, 
the screen shows a splash screen and other initialization indicator before the main display 
appears;  similar to Figure  3-2 above (may or may not display a Fault alarm). The LEDs 
on the display screen indicate the Sample, Calibration and Fault states; also on the screen 
is the gas concentration field (Conc), which displays real-time readouts for the primary 
gas and for the secondary gas if installed. The display screen also shows what mode the 
analyzer is currently in, as well as messages and data (Param). Along the bottom of the 
screen is a row of touch control buttons; only those that are currently applicable will have 
a label. Table 3-1  provides detailed information  for each component of the screen. 

Table 3-1. Display Screen and Touch Control Description 

Field 

Description/Function 

Status 

LEDs indicating the states of Sample, Calibration and Fault, as follows: 
Name 

Color 

State 

Definition 

SAMPLE  Green 

Off 
On 
 
Blinking 

Unit is not operating in sample mode, DAS is disabled. 
Sample Mode active; Front Panel Display being updated; DAS 

data being stored. 
Unit is operating in sample mode, front panel display being 

updated, DAS hold-off mode is ON, DAS disabled 

CAL 

Yellow 

Off 
On 
Blinking 

Auto Cal disabled 
Auto Cal enabled 
Unit is in  calibration mode 

FAULT 

Red 

Off 
Blinking 

No warnings exist 
Warnings exist 

Conc  

Displays the actual concentration of the sample gas currently being measured by the 

analyzer in the currently selected units of measure

 

Mode  

Displays the name of the analyzer’s current operating mode

 

Param 

Displays a variety of informational messages such as warning messages, operational data, 

test function values and response messages during interactive tasks.

 

Control 

Buttons 

Displays dynamic, context sensitive labels on each button, which is blank when inactive until 

applicable. 

 

Figure  3-3  shows how the front panel display is mapped to the menu charts illustrated in 
this manual. The Mode, Param (parameters), and Conc (gas concentration) fields in the 
display screen are represented across the top row of each menu chart. The eight touch 
control buttons along the bottom of the display screen are represented in the bottom row 
of each menu chart. 

 

CAUTION  – Avoid Damaging Touchscreen 

Do not use hard-surfaced instruments such as pens to operate the 

touchscreen. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов