Teledyne T101 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 375

Teledyne T101 Скачать руководство пользователя страница 128

Operating Instructions

Teledyne ML – T101 Operation Manual

124

4.7.12.

COM PORT TESTING

The serial ports can be tested for correct connection and output in the COMM menu. This
test sends a string of 256 ‘w’ characters to the selected COM port. While the test is
running, the red LED on the rear panel of the analyzer should flicker.

To initiate the test press the following button sequence.

SAMPLE RANGE = 500.0 PPB

H2S

=XXX.X

< TST TST > CAL

SETUP

SAMPLE

ENTER SETUP PASS : 818

8 1 8

ENTR

EXIT

SETUP X.X

PRIMARY SETUP MENU

CFG DAS

RNGE

PASS CLK

MORE

EXIT

SETUP X.X

SECONDARY SETUP MENU

COMM VARS

DIAG

EXIT

Select which

COM port to

test.

SETUP X.X

COMMUNICATIONS MENU

ID INET

COM1

COM2

EXIT

SETUP X.X

COM1 : TEST PORT

<SET

TEST

EXIT

SETUP X.X

TRANSMITTING TO COM1

<SET

TEST

EXIT

SETUP X.X

COM1 MODE:0

SET>

EDIT

EXIT

SETUP X.X COM1 BAUD RATE:19200

<SET

SET>

EDIT

EXIT

EXIT returns to

COMM menu

Test runs

automatically

4.8.

USING THE DATA ACQUISITION SYSTEM (DAS )

The  T101  analyzer contains a flexible and powerful, internal data acquisition system
(DAS  ) that enables the analyzer to store concentration and calibration data as well as a
host of diagnostic parameters. The DAS  of the T101  can store several  months of data,
depending on how it is configured. The data are stored in non-volatile memory and are
retained even when the instrument is powered off. Data are stored in plain text format for
easy retrieval and use in common data analysis programs (such as spreadsheet-type
programs).

The  DAS  is designed to be flexible. Users have full control over the type, length and
reporting time of the data. The DAS  permits users to access stored data through the
instrument’s front panel or its communication ports. Using APICOM, data can even be
retrieved automatically  to a remote computer for further processing.

The principal use of the DAS is logging data for trend analysis and predictive diagnostics,
which can assist in identifying possible problems before they affect the functionality of
the analyzer. The secondary use is for data analysis, documentation and archival in
electronic format.

To support the DAS functionality, Teledyne ML offers APICOM, a program that
provides a visual interface for remote or local setup, configuration and data retrieval of

«
...
126
127
128
129
130
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов