Teledyne T101 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 375

Teledyne T101 Скачать руководство пользователя страница 149

Teledyne ML – T101 Operation Manual

Remote Operation

145

Table 5-1. Status Output Pin Assignments

CONNECTOR PIN

STATUS

CONDITION (ON=CONDUCTING)

1

System Ok

ON if no faults are present.

2

Conc Valid

ON if concentration measurement is valid, OFF when invalid.

3

High Range

ON if unit is in high range of any AUTO range mode.

4

Zero Cal

ON whenever the instrument is in ZERO calibration mode.

5

Span Cal

ON whenever the instrument is in SPAN calibration mode.

6

Diag Mode

ON whenever the instrument is in DIAGNOSTIC mode.

7

Low Range

ON if unit is in low range of any AUTO range mode.

8

Unused

D

Emitter Bus

The emitters of the transistors on pins 1-8 are bussed

together. For most applications, this pin should be connected

to the circuit ground of the receiving device.

+

Dc Power

+ 5 VDC source, 30 mA maximum (combined rating with

Control Inputs)

Digital Ground The ground from the analyzer’s internal, 5/±15 VDC power

supply.

5.1.1.2.

Control Inputs

Control inputs allow the user to remotely initiate ZERO and SPAN calibration modes are
provided through a 10-pin connector labeled CONTROL IN on the analyzer’s rear panel.
These are opto-isolated, digital inputs that are activated when a 5 VDC signal from the
“U” pin is connected to the respective input pin.

Table 5-2. Control Input Pin Assignments

INPUT

STATUS

CONDITION WHEN ENABLED

A

External Zero Cal Zero calibration mode is activated. The mode field of the

display will read ZERO CAL R.

B

External Span Cal Span calibration mode is activated. The mode field of the

display will read SPAN CAL R.

C

External Low

Span Cal

Low span (mid-point) calibration mode is activated. The mode

field of the display will read LO CAL R.

D

Unused

E

Unused

F

Unused

Digital Ground

Provided to ground an external device (e.g., recorder).

U

DC Power For

Input Pull Ups

Input for +5 VDC required to activate inputs A - F. This voltage

can be taken from an external source or from the “+” pin.

+

In5v

Supply

Internal source of +5V which can be used to activate inputs

when connected to pin U.

«
...
147
148
149
150
151
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов