Teledyne T101 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 375

Teledyne T101 Скачать руководство пользователя страница 73

Teledyne ML – T101 Operation Manual

Operating Instructions

69

4.4.4.4.

Single Range Mode (SNGL)

The default range mode for the analyzer is single range, in which all analog concentration
outputs are set to the same reporting range. This reporting range can be set to any value
between 5.0 ppb and 20 000 ppb.

While the two outputs always have the same reporting range, the span and scaling of their
electronic signals may also be configured for different differently (e.g.,

A1

= 0-10 V;

A2

= 0-0.1 V).

To select

SNGLE

range mode and to set the upper limit of the range, press:

SAMPLE

ENTER SETUP PASS : 818

8 1 8

ENTR

EXIT

SETUP C.3

PRIMARY SETUP MENU

CFG DAS

RNGE

PASS CLK MORE

EXIT

SETUP C.3

RANGE CONTROL MENU

MODE

SET UNIT

EXIT

SETUP C.3

RANGE MODE:

SNGL

SNGL

IND AUTO

ENTR EXIT

EXIT

x 2 returns

to the main

SAMPLE

display

SETUP C.3

RANGE MODE:

SNGL

SNGL

IND AUTO

ENTR

EXIT

SETUP C.3

RANGE CONTROL MENU

MODE

SET

UNIT

EXIT

SETUP C.3

RANGE:

500.0 Conc

0 0

5

0 0 .0

ENTR

EXIT

SETUP C.3

RANGE CONTROL MENU

MODE

SET UNIT

EXIT

SAMPLE RANGE = 500.0 PPB

H2S

=XXX.X

< TST TST > CAL

SETUP

NOTE

On analyzers with the multigas option activated (see Sections 4.5.1 and 6.8) the concentration value will

switch back and forth between from “H2S=XXX.X” to “SO2=XXX.X” depending on which gas is currently

being measured.

«
...
71
72
73
74
75
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов