Siemens SIMATIC NET страница 65 Скачать руководство пользователя

Страница: 65 / 464

Configuration

3.1 System

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

The parameter has the following meaning:

Parameter

Description

Range of values / note

frame-size

Size of the MTU in bytes

64 ... 1514

At system start or when using the

restart

command with the option

memory

factory

, the

following defaults apply:

●

The size of the MTU is configured to 1500 bytes.

Result

The setting for the size of the MTU is configured.

Further notes

You can shut down the interface with the

shutdown complete

command.

You display this setting with the

show interface mtu

command.

You display this setting and other information with the

show interfaces

command.

3.1.10.8

shutdown

Description

With this command, you shut down the interface.

Requirement

You are in the Interface Configuration mode.
The command prompt is as follows:

cli(config-if-$$$)#

Syntax

Call the command without parameters:

shutdown complete

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды