Siemens SIMATIC NET страница 387 Скачать руководство пользователя

Страница: 387 / 464

Security and authentication

10.1 User rights management

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

387

10.1.4.3

username

Description

With this command, you change the password of the factory set default users "

user

" and

admin

Requirement

●

The user is logged in with the "admin" role.

●

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

username {user|admin} password <passwd>

The parameters have the following meaning:

Parameter

Description

Range of values / note

user

User name of the default user with

read access to the configuration

data.

Enter "

user

admin

User name of the default user with

read and write access to the con-

figuration data.

Enter "

admin

password

Keyword for a password

passwd

Value for the password

Enter the password.
The password must be at least 6 charac-

ters long.

Result

The password is changed.

Note
Changing the password in Trial mode
Even if you change the password in Trial mode, this change is saved immediately.

Further notes

You create a user with the

user-account

command.

You delete a user with the

no user-account

command.

You show the created users with the

show user-accounts

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды