Siemens SIMATIC NET Скачать руководство пользователя

Страница: 424 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

424

Configuration Manual, 10/2015, C79000-G8976-C351-05

10.2.5.7

vap security wpa-psk-passphrase (access point)

Description

With this command, you store the WPA(2) key that is used in WPA-PSK and WPA2-PSK

authentication.

Note
The key can be 8 to 63 ASCII characters or exactly 64 hexadecimal characters long. It

should be selected so that is complex for example consisting of random numbers, letters

(upper-/lowercase), have few repetitions and special characters. Do not use known names,

words or terms that could be guessed. If a SCALANCE W700 device is lost or if the key

becomes known, the key should be changed on all SCALANCE W700 devices to maintain

security.

Note
This command is available only in access point mode.

Requirement

●

WPA-PSK, WPA2-PSK or WPA(2)-PSK auto is set for the type of authentication.

You are in the Interface Configuration mode of the VAP interface.
The command prompt is as follows:

cli (config-if-vapX-0-Y)#

Syntax

Call up the command with the following parameters:

vap security wpa-psk-passphrase <string>

The parameter has the following meaning:

Parameter

Description

Range of values / note

string

WPA(2) key.

8....63ASCII

exactly

hex

Result

A WPA(2) key is specified.

Further notes

You display the settings with the

show wlan security <vapX 0/Y>

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды