Siemens SIMATIC NET страница 319 Скачать руководство пользователя

Страница: 319 / 464

Network protocols

7.3 DHCP server

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

319

7.3.3.7

pool-enable

Note
The command is only available with the following device:

•

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0

(US version))

•

SCALANCE W761-1 RJ45 in access point mode (article number): 6GK5761-1FC00-0AA0

and 6GK5761-1FC00-0AB0 (US version))

Description

With this command you specify that this IPv4 address band will be used.

Requirement

You are in the DHCPPOOL configuration mode.
The command prompt is as follows:

cli(config-dhcp-pool-<ID>)#

Syntax

Call the command without parameter assignment:

pool-enable

Result

The setting is enabled.

Note
If the IPv4 address band is enabled, DHCP options (option ...) and static assignments (static

leases) can no loner be edited.

Further notes

You display the setting with the

show ip dhcp-server pools

command.

You disable the setting with the

no pool-enable

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды