Siemens SIMATIC NET страница 399 Скачать руководство пользователя

Страница: 399 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

399

10.2.2.9

wlan security ap-radius-authenticator reauth-mode

Description

With this command, you specify who decides the time before the clients are forced to

reauthenticate.

Note
This command is available only in access point mode.

Requirement

You are in the WLAN Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-wlan)#

Syntax

Call up the command with the following parameters:

wlan security ap-radius-authenticator reauth-mode {show-modes | <mode>}

The parameters have the following meaning:

Parameters

Description

Range of values / note

show-modes

Lists the available values.

•

disabled

Function is disabled

•

server

Time management on the server

•

local

Local time management. You specify

the period of validity with the

wlan se-

curity ap-radius-authenticator

reauth-interval

command.

mode

Method of time management

Result

The function is configured.

Further notes

You display the setting with the

show wlan security ap-radius-authenticator

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды