Siemens SIMATIC NET Скачать руководство пользователя

Страница: 136 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

136

Configuration Manual, 10/2015, C79000-G8976-C351-05

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show wlan available-ap-list <wlan 0/X> [connected]

The parameters have the following meaning:

Parameter

Description

Range of values / note

wlan 0/X

WLAN interface

Enter a valid interface.

connected

shows the information of the access points

with which the client is connected.

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The access points to which the client can set up a wireless link are displayed.

6.1.1.7

show wlan basic

Description

This command displays the WLAN-basic configuration, for example, transmission standard,

frequency band.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды