Siemens SIMATIC NET страница 215 Скачать руководство пользователя

Страница: 215 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

215

6.1.7.3

wds partner wds-id (access point)

Description

With this command, you enter the WDS ID of the WDS partner.

Note
This command is available only in access point mode.

Requirement

You are in the Interface Configuration mode for the WDS interface.
The command prompt is as follows:

cli (config-if-wdsX-0-Y)#

Syntax

Call up the command with the following parameters:

wds partner wds-id <wds-id>

The parameter has the following meaning:

Parameters

Description

wds-id

WDS ID of the WDS partner

Result

The WDS ID is specified.

Further notes

You display the setting with the

show wlan wds <wdsX 0/Y>

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды