Siemens SIMATIC NET страница 323 Скачать руководство пользователя

Страница: 323 / 464

Network protocols

7.3 DHCP server

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

323

Result

The assignment is specified.

Further notes

You display the setting with the

show ip dhcp dhcp-server bindings

command.

You disable the IPv4 address band with the

no pool-enable

command.

You delete the assignment with the

no static-lease

command.

7.3.3.11

no static-lease

Note
The command is only available when the following requirements are met:

•

SCALANCE W722-1 RJ45 (article no.: 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-

0AB0 (US version))

•

SCALANCE W761-1 RJ45 in access point mode (article number): 6GK5761-1FC00-0AA0

and 6GK5761-1FC00-0AB0 (US version))

•

The IPv4 address band is not enabled.

Description

With this command, you delete the assignment of an IPv4 address to a MAC address.

Requirement

You are in the DHCPPOOL configuration mode.
The command prompt is as follows:

cli(config-dhcp-pool-<ID>)#

Syntax

Call up the command with the following parameters:

no static-lease { mac <mac-address> | client-id <string> }

The parameter has the following meaning:

Parameter

Description

Range of values / note

mac

Keyword for a MAC

address

mac-address

Unicast MAC address Specify the MAC address.

aa:bb:cc:dd:ee:ff

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды