Siemens SIMATIC NET страница 304 Скачать руководство пользователя

Страница: 304 / 464

Network protocols

7.3 DHCP server

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

304

Configuration Manual, 10/2015, C79000-G8976-C351-05

7.3.1.1

show ip dhcp-server pools

Note
The command is only available with the following device:

•

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0

(US version))

•

SCALANCE W761-1 RJ45 in access point mode (article number): 6GK5761-1FC00-0AA0

and 6GK5761-1FC00-0AB0 (US version))

Description

The command shows the DHCP server configuration of a specific IPv4 address band or all

IPv4 address bands and the corresponding DHCP options.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show ip dhcp-server pools [pool-id (1-5)]

The parameter has the following meaning:

Parameter

Description

Range of values / note

pool-id

ID of the addressed IPv4 address

band

1 ... 5
Only ID = 1 is supported.

Result

The configuration of the DHCP server and the DHCP options is displayed.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды