Siemens SIMATIC NET страница 252 Скачать руководство пользователя

Страница: 252 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

252

Configuration Manual, 10/2015, C79000-G8976-C351-05

Further notes

You can reset the setting to the default

mst

with the

no spanning-tree compatibility

command.
You can display the status of this function and other information with the

show spanning tree

detail

command.

You can display information about active ports with the

show spanning tree active

command.

6.3.3.4

no spanning-tree compatibility

Description

With this command, you reset the compatibility version of the protocol of the spanning tree

function to the default value.
The default value is MST.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call the command without parameters:

no spanning-tree compatibility

Result

The compatibility version is reset to the default value.

Further notes

You configure the setting with the

spanning-tree compatibility

command.

You can display the status of this function and other information with the

show spanning tree

detail

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды