Siemens SIMATIC NET страница 242 Скачать руководство пользователя

Страница: 242 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

242

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

show spanning-tree [{summary|blockedports|pathcost method}]

The parameters have the following meaning:

Parameter

Description

summary

Shows a summary

blockedports

Shows the blocked ports

pathcost method

Shows whether 16-bit (short) or 32 bit (long) values are used in the calcula-

tion

Result

The settings for the spanning tree function are displayed.

Further notes

You can show further settings for special aspects of the Spanning Tree Protocol with the

following commands:

●

show spanning-tree active

●

show spanning-tree bridge

●

show spanning-tree detail

●

show spanning-tree interface

●

show spanning-tree root

●

show spanning-tree mst

6.3.1.2

show spanning-tree active

Description

This command shows the settings for the active ports of the spanning tree function.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды