Siemens SIMATIC NET Скачать руководство пользователя

Страница: 285 / 464

Network protocols

7.1 IPv4 protocol

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

285

7.1.1.6

show ip dns cache

Description

This command shows the content of the DNS cache. The DNS cache buffers replies of the

DNS server for a brief time. This allows other queries for the same name to be replied to

directly without sending another query to the DNS server.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show ip dns cache

Result

The content of the DNS cache is displayed.

7.1.1.7

show ip dns name-server

Description

This command shows information about the DNS servers configured on the device. The

table contains the index, the address type (e.g. IPv4) as well as the IP address and the

origin.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show ip dns name-server

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды