Siemens SIMATIC NET страница 247 Скачать руководство пользователя

Страница: 247 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

247

6.3.1.8

show spanning-tree mst interface

Description

This command shows port-specific settings of a Multiple Spanning Tree configuration.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with one of the following parameter assignments:

show spanning-tree mst

[<instance-id(1-64)>] interface<interface-type><interface-id>

[{stats|hello-time|detail}]

The parameters have the following meaning:

Parameter

Description

Range of values / note

instance-id

Number of the instance or range of instances

whose settings are displayed

1 ... 64

interface-
type

Type or speed of the interface

Enter a valid interface.

interface-id

Module no. and port no. of the interface

stats

Shows the number of incoming and outgoing

packets for each path of the interface

hello-time

Shows the intervals at which the root switch

sends its "Hello" message to the other

switches

detail

Shows detailed information about the select-

ed interface

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The settings are displayed.

Further notes

You display the general settings for the Spanning Tree Protocol with the

show spanning-tree

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды