Siemens SIMATIC NET страница 178 Скачать руководство пользователя

Страница: 178 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

178

Configuration Manual, 10/2015, C79000-G8976-C351-05

6.1.5.25

wlan data rates-11abg selected only (access point)

Description

With this command, you enable the "Use selected data rates only" function. Only the data

transmission speeds you specified with the

wlan data rate-11abg

command are used.

Note
This command is available only in access point mode.

Requirement

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-if-wlan-0-X)#

●

The transmission standard IEEE 802.11a/b/g/n is set.

Syntax

Call the command without parameter assignment:

wlan data rates-11abg selected only

Result

The function is enabled.

Further notes

You display the setting with the

show wlan data rates

command.

You disable the function with the

no wlan data rates-11abg selected only

command.

You configure the data transmission speeds with the

wlan data rate-11abg

command.

You configure the transmission standard with the

wlan mode

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды