Siemens SIMATIC NET страница 409 Скачать руководство пользователя

Страница: 409 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

409

10.2.4.4

wlan security dot1x check-server-certificate (client)

Description

With this command, you enable the validation of the server certificate on the client.

Note
This command is only available in the client mode.

Requirement

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-wlan-context-x)#

Syntax

Call the command without parameter assignment:

wlan security dot1x check-server-certificate

Result

Validation is enabled.

Further notes

You display the settings with the

show wlan security

command.

You disable the validity check with the

no wlan security dot1x check-server-certificate

command (default setting).

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды