Siemens SIMATIC NET Скачать руководство пользователя

Страница: 57 / 464

Configuration

3.1 System

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

The parameters have the following meaning:

Parameter

Description

Range of values / note

off

PNIO is deactivated.

If a PROFINET connection is established; in

other words the PNIO AR status is "Online",

you cannot disable PNIO.

PNIO is activated.

When PNIO is turned on, EtherNet/IP is

turned off. The switchover from PNIO and

EtherNet/IP has no effect on DCP.

Result

PNIO is enabled or disabled after the next restart.

Further notes

You display the current PNIO configuration with the

show pnio

command.

3.1.9.10

system contact

Description

With this command, you enter contact information for the system.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

system contact <string>

The parameter has the following meaning:

Parameter

Description

Range of values / note

string

Input box for contact information

max. 255 characters

Result

The contact information is created in the system.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды