Siemens SIMATIC NET страница 54 Скачать руководство пользователя

Страница: 54 / 464

Configuration

3.1 System

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

The placeholder

$$$

is replaced by the following name of the interface:

Type of interface

Command prompt

wlan

cli(config-if-wlan-0-$)#

wds

cli(config-if-wds$-0-$)#

vap

cli(config-if-vap$-0-$)#

vlan

cli(config-if-vlan-$)#

fast-ethernet

cli(config-if-F-0-$)#

The placeholders

$-$

denote the numbering of the interface.

For the value ranges for the VLAN logical interface, refer to the upper table. You can only

call up interfaces that you created with the

vlan

command.

The ranges of values from the physical interfaces depend on the hardware configuration.

Further notes

You exit the Interface Configuration mode with the

end

exit

command.

You delete a logical interface with the

no interface

command.

You display the status and the configuration of the interfaces with the

show interfaces

command.

3.1.9.6

no interface

Description

With this command, you delete a logical interface.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

no interface{vlan<vlan-id(1-4094)>}

The parameters have the following meaning:

Parameter

Description

Range of values / note

vlan

Keyword for a VLAN connection

vlan-id

Number of the addressed VLAN

1 … 4094

Result

The logical interface is deleted.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды