Siemens SIMATIC NET страница 96 Скачать руководство пользователя

Страница: 96 / 464

Functions specific to SCALANCE

4.2 Signal recorder

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

The parameter has the following meaning:

Parameter

Description

Range of values / note

wlan 0/X

WLAN interface

Enter a valid interface.

The interval in milliseconds (ms) be-

tween acquisition of two measured

values

1 - 60000

sample_number

This parameter specifies how many

measured values will be recorded.

1 - 20000

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The recording is configured and will be started. The measured values are logged in files. If

these files already exist, they will be overwritten. If the set total number of measured values

is reached, the recording stops automatically. Use the

wlan signal-recorder <wlan 0/X>

stop

command to stop the recording early.

Further notes

You stop the recording early with the

wlan signal-recorder <wlan 0/X> stop

command.

You display the status of the signal recorder and the recording with the

show wlan signal-

recorder <wlan 0/X>

command.

4.2.3

wlan signal-recorder stop (client)

Description

With this command, you stop the recording with the signal recorder.

Note
This command is only available in the client mode.

Requirement

●

A recording was started.

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды