Siemens SIMATIC NET Скачать руководство пользователя страница 69

Страница: 69 / 464

Configuration

3.2 Load and Save

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

File type

Description

Save

Down-

load

WLANAuthlog

File with entries from the WLAN Authentication Log

(information on successful or failed authentication

attempts)

WLANCert

(in client mode only)

User certificate. You can specify a password for the

user certificate on the WBM page "Load&Save >

Password".

WLANServerCert

(in client mode only)

Server certificate

WLANSigRec

(in client mode only)

The zip file contains the following:

•

csv file with the measured values of the signal

recorder

•

pdf file with the measured values and an addition-

al graphic representation of the measured values.

You will find information about the measured values

and their graphic representation in the section "Signal

recorder (Page 94)".

WLANSpectru-

mAnalyzer

(Only in access

point mode)

The Zip file contains a csv file with the measured

values of the spectrum analyzer.
You will find information about the measured values

and their graphic representation in the section "Auto-

Hotspot".

3.2.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Siemens SIMATIC NET, Руководство по настройке, Страница: 69 / 464

Результаты поиска

Содержание SIMATIC NET

Отзывы: